![]() If you within an hour or so drive from Chehalis Wa, I can help you. 1968-1972 El Camino reproduction drivers side inner & outer rear wheelhouse. I see you're in Region 19 and if your close enough to drive, you welcome to stop by to see mine and/or, I can give you a hand on yours. 1968-1972 El Camino drivers side reproduction quarter panel (100 style). You can see one picture of the left hand panel in place if you look at the 3rd Gen Gallery of my 72, it's listed as Jims Northwest 72. Carlo El Camino Mopar Chevy 1968-1969 Camaro Custom Interior Un-Assembled Rear. Dimensionally, these panels run from approximately 1 behind the door to the rear tail lights. I should have taken progress pictures along the way, but didn't. 8 el camino interior trim & interior parts - 1978 el camino interior trim. One-piece stamping is identical in contour, fit and finish. Quarter Panel, 1968 - 72 El Camino RS (With Weld Through Primer) Dynacorn. It was a fun project and once started, it was a lot of fun to see a new big piece go on. Quarter Panel Patch, 1968 - 72 El Camino RS Dynacorn. Again, clear as mud huh?Īt any rate I did all the work by myself using large magnets to hold the new to old panel as I welded them up. Around the wheel opening, I made a few different cuts to get the old panel off of the inner panel so the new panel could be welded to it. THESE ARE MADE BY TRIM PARTS ANDARE SHOW. With the new panel hanging over the old one, I traced around the trimed new panel, lifted it off and using a cut-off wheel, cut off the old panel. THIS IS FOR A BRAND NEW PAIR OF 1968 1969 CHEVY EL CAMINO QUARTER PANEL EMBLEMS. I then '"hung" the new panel on the car with the old panel still in place and uncut. I cut the new panel about 1/2" behind the door and about 1/2" around the tail light. I left the new panel top bend on the new and cut off the old panel at the top of the bed rail. We cannot accept returns on sheet metal that has been primed, painted, or installed in any way.Hey JK, I replaced both quarters on my 72 several months ago. Quarter Panel, Quarter Panel, 1968-72 El Camino, Pair Part Number: OPG-1667160-PR Not Yet Reviewed Estimated Ship Date: (if ordered today) Drop Ship Freight Charge Special Order 453. Locate Chevelle 12 Bolt Rear End In Stock Today See our selection of. We recommend test fitting all sheet metal before bodywork and paint. WANTED: 10 or 12 bolt rear end 68 Camaro - 1234 (Spokane/surrounding area) Must be. Customer reviews and photos may be available to help you make the right purchase. Ground Up cannot be held responsible for items damaged in trucking unless this is noted.Just as original GM body panels, all reproduction sheet metal will require some sanding and bodywork and may require some trimming and shimming before priming. Buy 1968-72 El Camino Lower Rear Quarter Patch Panel-Right Hand at Amazon. Small dings, dents, and scratches are considered to be normal and are easily fixed during the normal filling, priming, and sanding of the item.If the sheet metal item is damaged during trucking, this must be noted on the Bill of Lading at the time of delivery so that the appropriate action can be taken. Want to learn more about the sheet metal products we offer? Check out our Sheet Metal FAQs!All sheet metal items must be inspected and signed for as arriving in good condition at time of delivery. ![]() These are extremely high quality pieces, so you can be sure to get the best fit possible. If your original El Camino quarter panel is dented or rotted right through to the ground, this exact reproduction quarter panel is the perfect replacement! There is no need to spend a fortune on an NOS quarter because this reproduction features a complete door jamb area and full roof sail panel. Quarter panel patch replacement on the Chevy El Camino Grant 7 AutoWorks 4.08K subscribers Subscribe Like Share Save 7.8K views 6 years ago For Tools, Parts & More. ![]()
0 Comments
Leave a Reply. |